Spray Plaster Product Specifications

Alltek is available in a number of different grades, allowing specification for a variety of uses and on many surfaces.  The technical product data for each grade is given below. Clicking on the underlined product will take you to that product's information & technical details.

• Alltek Orange
• Alltek Red, Universal 200
• Alltek Violet W.R 200
• Alltek Violet NL|83 COT
• Alltek Blue Course
• Alltek Blue Lissage
• Alltek Airless Red Fine
• Alltek Airless Violet WR
• Alltek Airless Lite

Alltek Orange


Product Information
Alltek Orange Superfine is a very fine graded filler and surfacing material which can be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration. It can be used on all types of interior building surfaces, such as cement or gypsum plaster, concrete, building boards and old painted surfaces, and over other Alltek products.

Alltek Orange Superfine is normally used as the final coat over Alltek Fine when a very smooth surface is required. It is applied as a skim coating over the whole surface. Supplied ready-mixed, Alltek Orange Superfine is water-based and non-toxic, and contains no asbestos fibres or other harmful ingredients.

Application is made by spray, using a mono pump type spray machine or an airless spray unit similar to Hemo 10. Apply in one or more coats, with intermittent drying. Make a first filling of any larger damages and holes using Alltek Fine. When used on old painted surfaces, ensure that the adhesion of the old paint is good.

Alltek Orange Superfine can be used on semi-exterior surfaces with adding of 1 part Portland cement to 3 parts Alltek Orange Superfine, with some extra water added for consistency. It can also be sprayed as a decorative textured coating and can, on ceilings, be left without any further decoration or painting. Alltek Orange Superfine can also be diluted with a little water and applied by roller, comb and other modelling tools to achieve a decorative finish.

Alltek Orange Superfine conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article Number: Superfine
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: white
Thickness Per Coat: >2mm
Packaging: 25kg plastic bags, 40 bags on one pallet
Density: 1.75 kg per litre
Solid Content: 73% nominal
Drying Time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand. Do not apply when air or surface temperature is below +5°C
Clean/Thin: With water
Flashing point - Fire Rating: None - class 0 surface spread of flame
Storage: Frost-free and dry, 6 months in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate with preservatives and rust inhibitors added.

Download this data sheet in MS Word document format.


Return to Top

---

Alltek Red Fine


Product information
Alltek Red Fine is a spray-applied filler and levelling compound which can be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration. It can be used on all types of interior building surfaces such as cement or gypsum plaster, concrete, building boards and old painted surfaces and over other Alltek products.

Alltek Red Fine is normally used as the final coat over Alltek Coarse. It is applied as a skim coating over the whole surface. Supplied ready-mixed with no mixing or adding of water required, Alltek Red Fine is water based, non-toxic and contains no asbestos fibres or other harmful ingredients.

Application is made by spray using a “mono pump” type spray machine. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Red Fine can be sprayed as a decorative textured coating and can, on ceilings, be left without any further decoration or painting. Alltek Red Fine can also be diluted with a little water and applied by roller, comb and other modelling tools to achieve a decorative finish.

Alltek Red Fine conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article no: finestd
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: white
Thickness per coat: >2mm
Packaging: 25kg plastic bags, 40 bags on one pallet
Density: 1.75 kg per litre
Solid content: 73% nominal
Drying time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand. Do not apply when air or surface temperature is below +5°C
Clean/thin: With water
Flash point – fire rating: None – class 0 surface spread of flame
Storage: Frost free and dry, 6 months in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate with preservatives and rust inhibitors added.
 
Download this data sheet in MS Word document format.


Return to Top

---

Alltek Violet W.R 200



Product Information
Alltek Violet Fine W.R. is a spray-applied filler and levelling compound, with additional binders for improved moisture-resistance, resilience and hardness, which can be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration. It can be used on all types of interior building surfaces such as concrete or gypsum plaster, cement, building boards and old painted surfaces and over other Alltek products. It is applied as a skim coating over the whole surface.

Supplied ready mixed with no mixing or adding of water required, Alltek Violet Fine W.R. is waterbased, non-toxic and contains no asbestos fibres or other harmful ingredients.

Application is made by spray, using a mono pump type spray machine. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Violet Fine W.R. can be used on semi exterior surfaces by adding 1 part Portland Cement to 3 parts Alltek Violet Fine W.R. with some extra water added for consistency. It can also be sprayed as a decorative textured coating and can, on ceilings, be left without any further decoration or painting.

Alltek Violet Fine W.R. conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article Number: fineviolet
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: white
Thickness Per Coat: >3 mm
Packaging: 25kg plastic bags, 40 bags on one pallet
Density: 1.75 kg per litre
Solid Content: 73% nominal
Drying Time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand. Do not apply when air or surface temperature is below +5°C
Clean / Thin: With water
Flashing point - Fire Rating: None - class 0 surface spread of flame
Storage: Frost free and dry, 6 months in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate with preservatives and rust Inhibitors added

Download this data sheet in MS Word document format


Return to Top

---

Alltek Violet NL|83 COT

Product Information
Alltek Violet NL COT 83.00 is a spray-applied filler and levelling compound with additional binders for improved water-resistance, resilience and hardness, to be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration. It can be used on all types of building surfaces such as cement or gypsum plaster, concrete, building boards and old painted surfaces and over other Alltek products.

Alltek Violet NL COT 83.00 can be applied interior as a skim coating over the whole surface. Application is made by spray, using a mono pump type spray machine. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Supplied ready-mixed, Alltek Violet NL COT 83.00 is waterbased, non-toxic and contains no asbestos fibres or other harmful ingredients.

Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Violet NL COT 83.00 can also be sprayed as a decorative textured coating, and can, on ceilings, be left without any further decoration or painting.

Alltek Violet NL COT 83.00 conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS, Dutch Standard COT and German Standard DIN.


Technical Data
Article Number: alltekcot
Standards: AFNOR/BS/SIS/DIN/ASTM/COT
Colour: white
Thickness Per Coat: <3 mm
Packaging: 9kg or 18kg plastic pails, or 25kg bags
Density: 1.75kg per litre
Solid Content: 73% nominal
Drying Time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand - do not use/apply when air or surface temperature is below +5°C
Clean / Thin: With water
Flashing point - Fire Rating: None - class 0 surface spread of flame
Storage: Frost-free and dry, 1 year in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate with preservatives and rust inhibitors added. 

Download this data sheet in MS Word document format.


Return to Top

---

 Alltek Blue Coarse


Product information
Alltek Blue Coarse is a spray-applied filler and levelling for use where thicker layers are required. Alltek Blue Coarse can be used over almost any interior surface to fill cracks, holes and undulations to improve the surface prior application of Alltek Fine. It can be used on aerated thermal concrete blockwork (e.g. Durox blocks) and on rough concrete surfaces in addition to thin joint cement/sandstone/gypsum blocks.

Alltek Blue Coarse is applied as a skim coating over the whole surface. Supplied ready-mixed, Alltek Blue Coarse is waterbased, non-toxic and contains no asbestos fibres or other harmful ingredients.

Application is made by spray, using a "mono pump" type spray machine. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Blue Coarse can be used on semi exterior surfaces by adding 1 part Portland Cement to 3 parts Alltek Blue Coarse, with some extra water added for consistency. It can also be sprayed as a decorative textured coating and can, when mixed with white Portland Cement, be left without any further decoration or painting.

Alltek Blue Coarse conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article no: coarse600
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: white/off white
Thickness per coat: >4 mm
Packaging 25-kg plastic bags, 40 bags on one pallet
Density: 1.65 kg per litre
Solid content: 73% nominal
Drying time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand. Do not apply when air or surface temperature is below +5°C
Clean/thin: With water
Flash point – fire rating: None – class 0 surface spread of flame
Storage: Frost-free and dry, 4 months in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate and natural sand with preservatives and rust inhibitors added.
Safety: Alkaline, avoid contact with skin or eyes, wash with liberal quantities of water. If in eyes, rinse immediately with water and contact your doctor.

Download this data sheet in MS Word document format.


Return to Top

---

Alltek Blue Lissage


Product Information
Alltek Blue Lissage is a spray applied filler and levelling compound to be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration.  It can be used on all types of interior building surfaces such as cement or gypsum plaster, concrete, building boards and old painted surfaces and over other Alltek products.
Alltek Blue Lissage is normally used as the final coat over coarser grades of Alltek. Alltek Blue Lissage is applied as a skim coating over the whole surface.

Supplied ready-mixed, Alltek Blue Lissage is water based, non-toxic and contains no asbestos fibres or other harmful ingredients.

Application is made by spray, using a mono pump type spray machine. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Blue Lissage can be sprayed as a decorative textured coating and can, on ceilings, be left without any further decoration or painting. Alltek Blue Lissage can also be diluted with a little water and applied by roller, comb and other modelling tools to achieve a decorative finish.

Alltek Blue Lissage conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article Number: lissage
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: Beige
Thickness Per Coat: >2mm
Packaging: 25kg plastic bags, 40 bags on one pallet
Density: 1.75 kg per litre
Solid Content: 73% nominal
Drying Time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand. Do not apply when air or surface temperature is below +5°C
Clean / Thin: With water
Flashing point - Fire Rating: None - class 0 surface spread of flame
Storage: Frost-free and dry, 6 months in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate and natural fine graded sand with preservatives and rust inhibitors added.

Download this data sheet in MS Word document format.


Return to Top

---

Alltek Red Fine Airless 180


Product Information
Alltek Red Fine Airless is a spray-applied filler and levelling compound to be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration. It can be used on all types of interior building surfaces such as cement or gypsum plaster, concrete, building boards and old painted surfaces and over other Alltek products.  It is specially designed for application with airless piston pump spray equipment.

Alltek Red Fine Airless is normally used as the final coat over Alltek Coarse, and is applied as a skim coating over the whole surface.

Supplied ready-mixed, Alltek Red Fine Airless is water based, non-toxic and contains no asbestos fibres or other harmful ingredients.

Application is made by spray using an airless piston pump or mono pump type spray machine. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Red Fine Airless Standard cannot be mixed with cement and is intended only for use on interior dry surfaces, i.e. not to be used in bathrooms, showers etc.

Alltek Red Fine Airless can be sprayed as a decorative textured coating and can, on ceilings, be left without any further decoration or painting. It can also be diluted with a little water and applied by roller, comb and other modelling tools to achieve a decorative finish.

Alltek Red Fine Airless conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article Number: fineal
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: white
Thickness Per Coat: >2mm
Packaging: 25kg plastic bags, 40 bags on one pallet
Density: 1.75 kg per litre
Solid Content: 73% nominal
Drying Time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: By spray or by hand. Do not use/apply when air or surface temperature is below +5°C
Clean / Thin: With water
Flashing point - Fire Rating: None-  class 0 surface spread of flame
Storage: Frost free and dry 6 months in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate with preservatives and rust inhibitors added.

Download this data sheet in MS Word document format.


Return to Top

---

Alltek Airless Violet WR


Product Information
Alltek Violet Fine Airless WR is a spray-applied filler and levelling compound with viscosity and rheology adapted for spraying with airless spraying equipment. Alltek Violet Fine airless W.R. has additional binders for improved moisture-resistance, resilience and hardness, and can be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration. It can be used on all types of interior building surfaces such as cement or gypsum plaster, concrete, building boards and old painted surfaces and over other Alltek products. Alltek Violet Fine Airless WR is specially designed for spray with airless piston pump spraying equipment.

Alltek Violet Fine Airless WR is applied as a skim coating over the whole surface and is supplied ready-mixed. Alltek Violet Fine Airless WR is waterbased, non-toxic and contains no asbestos fibres or other harmful ingredients.

Application is made by spray using an airless type spray machine such as Hemo 10, Graco 1500 or Wagner EP 3000 or traditional mono pumps. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Violet Fine Airless WR can be used on semi-exterior surfaces by adding 1 part Portland Cement to 3 parts Alltek Violet Fine Airless WR, with some extra water added for consistency. When mixed with cement, do not spray with airless spraying equipment as damage to the machine can occur.

Alltek Violet Fine Airless WR can be sprayed as a decorative textured coating and can, on ceilings, be left without any further decoration or painting.

Alltek Violet Fine Airless WR conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article Number: violetal
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: white
Thickness Per Coat: >2 mm
Packaging: 25kg plastic bags, 40 bags on one pallet
Density: 1.75 kg per litre
Solid Content: 73% nominal
Drying Time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand. Do not apply when air or surface temperature is below +5°C
Clean / Thin: With water
Flashing point - Fire Rating: None class 0 surface spread of flame
Storage: Frost free and dry, 6 months in unopened container
Toxicity: Free from toxic matter

Download this data sheet in MS Word document format.


Return to Top

---

Alltek Airless Lite



Product Information
Alltek Lite Airless is a light weight spray-applied filler and levelling compound to be used over almost any interior surface to fill cracks, holes and undulations to improve the surface for final decoration.  It can be used on all types of interior building surfaces such as cement or gypsum plaster, concrete, building boards and old painted surfaces and over other Alltek products.

Alltek Lite Airless is normally used as the final coat over Alltek Coarse and is applied as a skim coating over the whole surface.

Supplied ready-mixed, Alltek Lite Airless is water based, non-toxic and contains no asbestos fibres or other harmful ingredients. Application is made by spray, using an airless piston pump or mono pump type spray machines. Apply in one or several coats, with intermittent drying. Make a first filling of any larger damages and undulations. When used on old painted surfaces ensure that the adhesion of the old paint is good.

Alltek Lite Airless can be sprayed as a decorative textured coating and can on ceilings be left without any further decoration or painting. It can also be diluted with a little water and applied by roller, comb and other modelling tools to achieve a decorative finish.

Alltek Lite Airless conforms, where applicable, to French Standard AFNOR, British Standard BS, American standard ASTM, Swedish Standard SIS and German Standard DIN.


Technical Data
Article Number: liteal
Standards: AFNOR/BS/SIS/DIN/ASTM
Colour: white
Thickness Per Coat: >2mm
Packaging: 15 litre plastic bags, 40 bags/pallet; or 15 litre plastic bucket, 33 buckets/pallet
Density: 1.1 kg per litre
Solid Content: 59% nominal (by weight)
Drying Time: 12 hours per mm with temp +15 rh 75-85%
Coverage: 1 litre per square meter and mm thickness
Application: by spray or by hand. Do not apply when air or surface temperature is below +5°C
Clean / Thin: With water
Flashing point - Fire Rating: None - class 0 surface spread of flame
Storage: Frost-free and dry, 1 year in unopened container
Toxicity: Free from toxic matter
General: Water borne dispersion filler based on calcium carbonate and lightweight fillers with preservatives and rust inhibitors added.

Download this data sheet in MS Word document format.


Return to Top